收藏本站
DS1992/DS1993
Copy Scratchpad [55h]
This command is used to copy data from the scratchpad to memory. After issuing the copy scratchpad
command, the user must provide a 3-byte authorization pattern. This pattern must exactly match the data
contained in the three address registers (TA1, TA2, E/S, in that order). If the pattern matches, the AA
(Authorization Accepted) flag is set and the copy begins. A logic 0 is transmitted after the data has been
copied until the user issues a reset pulse. Any attempt to reset the part is ignored while the copy is in
progress. Copy typically takes 30 μ s.
The data to be copied is determined by the three address registers. The scratchpad data from the
beginning offset through the ending offset is copied to memory, starting at the target address. Anywhere
from 1 to 32 Bytes can be copied to memory with this command. Whole Bytes are copied even if only
partially written. The AA flag is cleared only by executing a write scratchpad command.
Read Memory [F0h]
The read memory command can be used to read the entire memory. After issuing the command, the user
must provide the 2-Byte target address. After the two Bytes, the user reads data beginning from the target
address and may continue until the end of memory, at which point logic 1’s are read. It is important to
realize that the target address registers contains the address provided. The ending offset/data status Byte
is unaffected.
The hardware of the DS199x provides a means to accomplish error-free writing to the memory section.
To safeguard reading data in the 1-Wire environment and to simultaneously speed up data transfers, it is
recommended to packetize data into data packets of the size of one memory page each. Such a packet
would typically store a 16-bit CRC with each page of data to ensure rapid, error-free data transfers that
eliminate having to read a page multiple times to determine if the received data is correct or not. (See
Application Note 114 for the recommended file structure to be used with the 1-Wire environment.)
6 of 17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS1995L-F5+ IBUTTON MEMORY 16KBit F5
DS1996L-F5+ IBUTTON MEMORY 64KBit F5
DS9092K# KIT IBUTTON STARTER
DS9502P+T&R DIODE ESD PROTECTION 6-TSOC
DS9503P+ DIODE ESD PROTECTION W/RES 6TSOC
DSL70 E6327 DIODES TVS ARRAY R-R SOT-143
DT-2R48-B6 SWITCH PLUNGER DPDT 10A SCREW
DT-2R722-A7 SWITCH PLUNGER DPDT 10A SCREW
相关代理商/技术参数
DS1993L-F5-C01 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1994 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:4kb Plus Time Memory iButton
DS1994-LF5 制造商: 功能描述: 制造商:undefined 功能描述:
DS1994L-F5 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1994L-F5+ 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1994L-F5-W 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1994-LFS 制造商: 功能描述: 制造商:undefined 功能描述:
DS1995 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:16-kbit Memory iButton